<xml>
  <damage_repair>
    <component name="clean">
      <repair_info max_condition="40" time="8" />
      <repair_info max_condition="100" time="6" />
    </component>
    <component name="engine" clean_reduction="1" >
      <repair_info max_condition="60" time="15" />
      <repair_info max_condition="100" time="5" />
    </component>
    <component name="gearbox" clean_reduction="3">
      <repair_info max_condition="100" time="20" />
    </component>
    <component name="driveshaft" clean_reduction="2">
      <repair_info max_condition="100" time="10" />
    </component>
    <component name="exhaust" clean_reduction="2">
      <repair_info max_condition="100" time="12" />
    </component>
    <component name="bodywork" clean_reduction="2">
      <repair_info max_condition="50" time="20" />
      <repair_info max_condition="100" time="10" />
    </component>
    <component name="cooling" clean_reduction="2">
      <repair_info max_condition="100" time="15" />
    </component>
    <component name="suspension" clean_reduction="2">
      <repair_info max_condition="80" time="18" />
      <repair_info max_condition="100" time="12" />
    </component>
    <component name="wheels" clean_reduction="1">
      <repair_info max_condition="100" time="5" />
    </component>
    <component name="turbo" clean_reduction="1">
      <repair_info max_condition="100" time="10" />
    </component>
    
    <!--
    This is the minimum condition under which the exhaust is still allowable on the race track.
    It should be a value between 0 and 1 representing a percentage from 0 to 100 percent. (i.e. 0.4 = 40%)
    -->
    <exhaust_min_legal_condition value="0.4" />
    <!--
    This is the minimum condition that the car's rear bodywork must have to be able to repair the exhaust
    It should be a value between 0 and 1 representing a percentage from 0 to 100 percent. (i.e. 0.8 = 80%)
    -->
    <bodywork_min_rear_condition_for_exhaust value="1.0" />
    
    <damage_icon_colours>
      <condition max="25" animState="damage_5" />
      <condition max="50" animState="damage_4" />
      <condition max="75" animState="damage_3" />
      <condition max="99" animState="damage_2" />
      <condition max="100" animState="damage_1" />
    </damage_icon_colours>
    
  </damage_repair>
  
  <vehicle_setup>
    <!-- These represent the multiplication applied to the gear ratios when the quick set slider is at the value indicated -->
    <gear_ratios>
      <preset value="0" multiplier="0.8" />
      <preset value="1" multiplier="0.9" />
      <preset value="2" multiplier="1.0" /> <!-- Don't change this line, it's the default! -->
      <preset value="3" multiplier="1.1" />
      <preset value="4" multiplier="1.2" />
    </gear_ratios>
  </vehicle_setup>
  
  <autorepeat>
    <type id="list" initial_delay="0.35" frequency="0.08" max_rep_delay="2.0" max_frequency="0.01" />
    <type id="adjustableitem" initialdelay="0.35" frequency="0.08" />
    <type id="scroller_defaults" initial_delay="0.2" initial_per_second="5" time_to_max_speed="3" max_per_second="50" />
  </autorepeat>
  
  <audio>
    <volume_level data="volume_soundfx" default="10" max="10" />
    <volume_level data="volume_engine" default="10" max="10" />
    <volume_level data="volume_speech" default="10" max="10" />
    <volume_level data="volume_music" default="10" max="10" />
    <volume_level data="volume_headset" default="10" max="10" />
  </audio>
  
  <default_livery>
    <item data="livery_number"            id="18" />
    <item data="livery_pattern"           id="53" />
    <item data="livery_primary_colour"    id="48" />
    <item data="livery_secondary_colour"  id="61" />
    <item data="livery_tertiary_colour"   id="65" />
  </default_livery>
      
  <!--
    This data represents the advanced controller setup information for the sliders in the front end/pause menu
    Each slider info has the following attributes:
      data - The identifier for the data, don't change this
      default - The default value for the slider, where 0 is the minimum, and maxVal is the maximum
      maxVal - The maximum value the slider can display, must be greater than or equal to default
      saturation - existence of this attribute indicates that the data relates to a wheel setup slider,
             while its value indicates whether it's a saturation or deadzone type, don't change this
      type - The action type for this data, don't change this
  -->
  <adv_controls>
    <slider_info data="feedback_force" default="5" max="10" />		<!-- Represents the strength of the centering force on an ffb device -->
    <slider_info data="feedback_friction" default="5" max="10" />	<!-- Represents the resistance to movement on an ffb device -->
    <slider_info data="feedback_effects" default="5" max="10" />	<!-- Represents the strength of ffb or vibration effects (e.g. when damage is caused) -->
    <slider_info data="wheelLinearity" default="14" max="20" />
    <slider_info data="steeringSaturation" default="20" max="20" saturation="true" type="steer" />
    <slider_info data="steeringDeadzone" default="0" max="20" saturation="false" type="steer" />
    <slider_info data="accelerateSaturation" default="20" max="20" saturation="true" type="acc" />
    <slider_info data="accelerateDeadzone" default="0" max="20" saturation="false" type="acc" />
    <slider_info data="breakSaturation" default="20" max="20" saturation="true" type="brk" />
    <slider_info data="breakDeadzone" default="0" max="20" saturation="false" type="brk" />
  </adv_controls>

  <overlay_chat>
      <info_item button="select" stringid="net_buttontext_send_message" />
      <info_item button="back" stringid="cancel" />
      <info_item button="pc_home" stringid="default_buttontext_back" />
  </overlay_chat>
  
</xml>
